# M2HATS experiment overview

## Purpose of this document

This document provides a practical scientific overview of the **Multipoint Monin-Obukhov Similarity Theory Horizontal Array Turbulence Study (M2HATS)**.

It is intended for students, collaborators, outside researchers, and AI-assisted workflows that need enough context to understand:

- why M2HATS was conducted;
- where and when it took place;
- the basic geometry of the experiment;
- the main observing systems;
- how the different measurements complement one another;
- and why the data set is unusual.

This is **not** a replacement for the formal M2HATS experiment paper or the detailed NCAR/EOL data reports.

The primary experiment reference is:

> Tong, C., S. D. Mayor, S. P. Oncley, C. Roden, W. O. J. Brown, S. M. Spuler, M. Hayman, B. M. Morley, J. Witte, P. Dérian, S. F. J. De Wekker, J. Sun, K. Barskov, and D. Pourabdollah (2026), "Multipoint Monin-Obukhov Similarity Theory Horizontal Array Turbulence Study (M2HATS)," *Bulletin of the American Meteorological Society*, 107, E501-E527.  
> https://doi.org/10.1175/BAMS-D-24-0037.1

For public data locations, see:

```text
M2HATS_data_locations.md
```

---

# 1. What M2HATS was

**M2HATS** stands for:

**Multipoint Monin-Obukhov Similarity Theory Horizontal Array Turbulence Study**

M2HATS was a major atmospheric surface-layer field experiment conducted near **Tonopah, Nevada**, during the summer of 2023.

The principal investigators were:

- **Chenning Tong**, Clemson University;
- **Shane D. Mayor**, California State University, Chico.

The NSF National Center for Atmospheric Research Earth Observing Laboratory (**NSF NCAR/EOL**) provided major observing systems, field support, data acquisition, processing, and archiving. Additional investigators and institutions contributed specialized measurements and analysis.

The formal M2HATS measurement period was:

```text
23 July - 23 September 2023
```

Some individual instruments collected data before or after those dates during setup and teardown, so data directories may contain observations outside the formal campaign period.

---

# 2. Why M2HATS was conducted

The original scientific purpose of M2HATS was to obtain field measurements needed to test predictions of **multipoint Monin-Obukhov similarity theory (MMO)**.

Classic Monin-Obukhov similarity theory (MOST) has been extraordinarily useful for describing the atmospheric surface layer, but it is fundamentally a single-point similarity framework. Important surface-layer statistics, especially horizontal velocity variances and spectra at scales larger than the measurement height, show behavior under convective conditions that is not fully described by classic MOST.

MMO extends the similarity framework to **multipoint statistics**, such as:

- spatial correlations;
- spectra;
- structure functions;
- cospectra.

A particularly important MMO prediction concerns **ring-integrated two-dimensional spectra** as functions of horizontal wavenumber magnitude.

Testing these predictions requires information about turbulence over a range of horizontal spatial scales. Conventional measurements at one tower or one point are not sufficient.

M2HATS was therefore designed around an unusually dense combination of:

- a long horizontal array of sonic anemometers;
- spatial remote sensing;
- vertical profiling;
- surface flux measurements;
- temperature measurements over extended horizontal distances.

The result is a data set that spans spatial scales from meters to kilometers.

Although M2HATS was designed primarily to test MMO, the observations are also useful for many other studies of atmospheric surface-layer and boundary-layer structure.

---

# 3. Field site

M2HATS was conducted in the **Ralston Valley**, approximately 13 km east-southeast of the town of Tonopah, Nevada, and near the Tonopah Airport.

The experiment site was at roughly:

```text
1655 m above mean sea level
```

The Ralston Valley is a broad north-south-oriented desert valley between mountain ranges.

The site was selected because it has several characteristics that are particularly favorable for surface-layer turbulence studies:

- a broad and relatively flat valley floor;
- long unobstructed fetch;
- short and fairly uniform desert vegetation;
- few nearby buildings, trees, or agricultural obstacles;
- very small surface latent heat flux during much of the campaign;
- reliable daytime southerly winds.

The valley floor near the experiment was approximately 16 km wide, and the upwind fetch to the south extended for many kilometers.

The prevailing daytime flow was commonly from the south and was often strong, of order 10 m/s.

These conditions were especially useful because the main sonic-anemometer array was designed to lie approximately **perpendicular to the prevailing wind**.

---

# 4. The central experimental idea

The centerpiece of M2HATS was a long crosswind array of sonic anemometers.

The array consisted of:

```text
50 sonic-anemometer towers
5 m tower spacing
245 m total array length
```

The towers were approximately 4.5 m tall, and the sonic anemometers were mounted at approximately **4.4 m above ground level**.

The array sites are named:

```text
t0p, t01, t02, ... , t49
```

from west to east.

The array was oriented along a line toward approximately **80 degrees azimuth**, nearly perpendicular to the prevailing daytime southerly winds.

The dense crosswind measurements can be combined with **Taylor's hypothesis** to convert temporal measurements into information along the streamwise direction.

Conceptually:

```text
50 simultaneous points across the wind
                +
time evolution as turbulence advects past the array
                |
                v
quasi-two-dimensional information about turbulence
```

This approach had been used in earlier HATS-type experiments, but the 245-m M2HATS array was substantially longer than previous arrays of this type.

That extended the directly observed range of horizontal turbulence scales.

---

# 5. Multilevel flux towers

Two multilevel towers were deployed near the eastern end of the horizontal array.

They were treated together as the ISFS site named:

```text
t0
```

The two structures were:

- a short approximately 6-m Rohn tower;
- a 30-m trailer tower.

Together they provided measurements at approximately:

```text
0.5, 1, 2, 3, 4, 7, 15, and 28 m
```

Measurements included combinations of:

- three-dimensional wind;
- sonic temperature;
- air temperature;
- relative humidity;
- pressure;
- water vapor;
- carbon dioxide;
- turbulent fluxes.

The short and tall towers were separated physically so that the large base structure of the 30-m tower would not strongly disturb measurements at the lowest levels.

## Early-campaign tower relocation

The final geometry was not established immediately on the first day.

The 30-m tower and short tower were moved during the first week because their initial separation and differing terrain/vegetation environments produced discontinuities in the combined vertical profiles.

The NCAR ISFS report recommends **not using the combined t0 wind profiles before 31 July 2023** for analyses requiring a consistent multilevel profile.

Users doing detailed tower analysis should consult the ISFS data report rather than relying only on this overview.

---

# 6. REAL scanning aerosol lidar

The **Raman-shifted Eye-safe Aerosol Lidar (REAL)** was operated by California State University, Chico.

REAL is a rapidly scanning elastic-backscatter polarization lidar.

It does **not** directly measure Doppler wind velocity.

At M2HATS, REAL was deployed to make rapidly repeated, nearly horizontal images of aerosol backscatter in the atmospheric surface layer.

For the routine M2HATS scans, REAL was operated approximately as follows:

```text
elevation:       0 degrees
azimuth sector:  60-120 degrees
scan rate:       about 4 degrees per second
scan duration:   about 17 seconds
laser PRF:       10 Hz
range sampling:  1.5 m
angular sampling: about 0.4 degrees
```

The scan plane was approximately **5 m above ground level** in the region of primary scientific interest.

Sequential aerosol images can be processed with the **Typhoon** wavelet-based optical-flow system to estimate two-component horizontal motion fields.

For a general description of REAL, see:

```text
REAL_instrument_description.md
```

For the raw REAL data format:

```text
REAL_bscan_data_file_format.md
```

For the current signal-processing sequence:

```text
REAL_bscan_signal_processing.md
```

---

# 7. The intentional REAL-sonic-array geometry

The relationship between REAL and the 50-sonic array was deliberately designed.

REAL was positioned so that a beam pointing toward approximately:

```text
80 degrees azimuth
```

was **collinear with the sonic-anemometer array**.

The array occupied approximately:

```text
1175-1425 m range from REAL
```

along that direction.

This geometry was useful for several reasons.

First, it provided a direct spatial relationship between the lidar sampling geometry and the in-situ array.

Second, viewing the towers nearly end-on reduced their angular silhouette from the lidar's perspective. This helped minimize the region affected by hard-target returns from towers and guy wires if the beam passed close to the array.

Third, it made possible direct comparisons among spatial measurements from REAL, the sonic array, and the Doppler-lidar measurements aligned along or near the same direction.

REAL's laser beam was aimed to scan just above the tower array.

---

# 8. REAL observations and atmospheric conditions

REAL generally detected aerosol backscatter to ranges of at least approximately 2 km during M2HATS.

However, seeing aerosol return is not the same as having spatial aerosol structure suitable for motion estimation.

The most useful conditions for REAL motion estimation were generally:

- daytime;
- dry;
- convective;
- moderate or strong winds;
- prevailing flow from the south.

Under these conditions, wind gusts interacting with the dry surface often produced strong small-scale spatial variability in aerosol backscatter.

Nighttime periods were usually less favorable for motion estimation because winds were often lighter and from the north.

The remnants of Tropical Storm Hilary affected the site from about 19-21 August 2023. The rain altered the normally dry surface and was followed by a substantial reduction in the spatial aerosol variability observed by REAL.

---

# 9. NCAR Integrated Surface Flux System (ISFS)

NSF NCAR/EOL's **Integrated Surface Flux System (ISFS)** operated the horizontal array, multilevel towers, and a variety of supporting surface measurements.

The 50 horizontal-array towers each carried a Campbell Scientific CSAT-family three-dimensional sonic anemometer.

Different CSAT models were used, with native sampling rates of approximately:

```text
30, 50, or 60 samples per second
```

depending on the instrument.

Additional measurements on selected array towers included:

- H2O/CO2 infrared gas analyzers;
- temperature and relative humidity;
- fast-response nanobarometers.

Additional surface measurements included:

- soil temperature;
- soil moisture;
- soil heat flux;
- soil thermal properties;
- four-component radiation;
- wetness sensors;
- a disdrometer.

The detailed sensor list, exact site coordinates, sampling rates, variable names, quality control, tilt corrections, and data caveats are documented in:

> **M2HATS NSF NCAR/EOL ISFS Surface Meteorology and Flux Products Data Report**

The public Chico copy is available under the ISFS data directory.

A separate M2HATS ISFS Markdown guide should be used for practical access to those netCDF files.

---

# 10. Doppler wind lidars

The NCAR Integrated Sounding System (**ISS**) operated three Doppler wind lidars during M2HATS:

1. **Vaisala/Leosphere WindCube 200S scanning lidar**;
2. **University of Virginia Halo-Photonics Streamline XR lidar**;
3. **Metek Halo-Photonics Streamline XR lidar**.

The WindCube performed multiple scan modes, including:

- continuous conical PPI scans for wind profiles;
- low-elevation sector scans over the study area;
- RHI scans;
- vertical stares.

The two Halo systems were used primarily for staring and periodic wind-profile measurements.

One of the important experimental geometries involved a Doppler lidar directed approximately along the sonic-array direction so that radial-velocity measurements could complement the spatial information from the sonic array and REAL.

The ISS wind-lidar data report should be consulted for exact scan IDs, dates, pointing angles, and data products.

---

# 11. Radar wind profilers and RASS

M2HATS included:

- a **449-MHz radar wind profiler**;
- a **915-MHz radar wind profiler**;
- a **Radio Acoustic Sounding System (RASS)**.

These systems provided measurements of the wind and virtual-temperature structure above the surface layer and helped connect the near-surface array measurements to the deeper atmospheric boundary layer.

They were also useful for estimating boundary-layer depth and providing meteorological context for individual REAL and sonic-array events.

Time-height images from these systems are included in the public M2HATS daily context pages.

---

# 12. MicroPulse Differential Absorption Lidars

Two **MicroPulse Differential Absorption Lidar (MPD)** systems were deployed.

The MPDs provided vertical profiling of:

- water vapor;
- aerosol backscatter;
- temperature.

The M2HATS deployment included new calibrated temperature retrievals.

These measurements help connect surface-layer measurements to the thermodynamic structure of the deeper boundary layer.

---

# 13. Fiber-optic distributed temperature sensing

A fiber-optic **distributed temperature sensing (DTS)** system was deployed approximately parallel to the horizontal sonic array.

The optical-fiber path extended approximately 1 km, with the 245-m sonic array located within the central part of the measurement line.

The fiber was mounted approximately 2.3 m above ground.

The DTS produced spatially dense temperature measurements along the crosswind direction.

Like the sonic array, these measurements can be combined with advection/Taylor-hypothesis concepts to obtain quasi-two-dimensional information, in this case about temperature structure.

---

# 14. Radiosondes and drone profiling

Radiosondes were launched routinely during M2HATS to provide vertical profiles through the boundary layer and lower atmosphere.

The ISS program commonly launched radiosondes at approximately:

```text
10:00 local time
15:00 local time
```

A **CopterSonde 2** quadcopter was also operated during part of the campaign.

During its main operating period, it profiled temperature up to approximately 900 m repeatedly during daytime convective conditions.

These observations complemented:

- tower profiles;
- MPD temperature retrievals;
- RASS measurements.

---

# 15. Other ISS surface and context measurements

The ISS observing system also included supporting instruments such as:

- surface meteorological stations;
- a Vaisala CL61 ceilometer;
- PurpleAir aerosol sensors;
- webcams;
- visibility and radiation sensors.

These measurements are useful for environmental context, instrument intercomparison, and interpretation of particular events.

Not all ISS products are currently mirrored on the Chico State lidar server.

For the complete project archive, use the NSF NCAR/EOL M2HATS archive.

---

# 16. How the observing systems fit together

One of the strengths of M2HATS is that different instruments were designed to cover different spatial scales, heights, and quantities.

A simplified view is:

| Observing system | Main role in M2HATS |
|---|---|
| 50-sonic horizontal array | High-frequency turbulence across 245 m |
| Multilevel flux towers | Near-surface vertical profiles, fluxes, stability |
| REAL | Spatial aerosol imagery and motion-estimated horizontal flow over roughly 100-m to kilometer scales |
| Along-array Doppler lidar | Radial-velocity information extending beyond the sonic array |
| Other Doppler lidars | Boundary-layer wind profiles and scanning context |
| 449/915-MHz radar profilers | Wind profiles and boundary-layer structure |
| RASS | Virtual-temperature profiles |
| MPDs | Water vapor, aerosol, and temperature profiles |
| DTS | Dense horizontal temperature measurements |
| Radiosondes | Full thermodynamic and wind profiles |
| CopterSonde | Repeated lower-boundary-layer temperature profiles |
| Surface met / ceilometer / cameras | Supporting meteorological and visual context |

No single instrument spans the entire range of scales and heights needed for M2HATS.

The scientific power of the experiment comes from using them together.

---

# 17. A useful mental picture of the experiment

A new user can think of M2HATS as two connected observing regions.

## Western/base-instrument region

Near the utility-served base area were:

- REAL;
- ISS Doppler lidars;
- radar wind profilers;
- MPDs;
- ceilometer;
- surface meteorology;
- radiosonde operations;
- other profiling systems.

## Eastern surface-layer array region

More than 1 km east were:

- the 245-m sonic-anemometer array;
- the multilevel flux towers;
- the DTS line;
- supporting soil, radiation, pressure, and surface measurements.

REAL and several other remote sensors looked from the western region toward or across the eastern array region.

This geometry combined:

```text
dense in-situ measurements
        +
horizontal spatial imaging
        +
remote wind measurements
        +
vertical profiling
```

into a single coordinated experiment.

The measurement schematic in Fig. 1 of Tong et al. (2026) and the site map in Fig. 3 are especially useful visual references for understanding this geometry.

---

# 18. Why the data set is unusual

M2HATS is unusual because it combines several capabilities that are rarely available together:

1. **Fifty simultaneous high-frequency sonic measurements across 245 m.**
2. **Meter-scale spatial aerosol imagery over kilometer-scale areas.**
3. **Motion-estimated two-component horizontal flow fields from REAL imagery.**
4. **Multiple independent Doppler-lidar measurements.**
5. **Vertical wind and temperature profiling through much of the boundary layer.**
6. **Dense horizontal temperature measurements from DTS.**
7. **Multilevel flux measurements near the surface.**
8. **Detailed meteorological context from profilers, soundings, lidars, and surface sensors.**

This makes the archive useful not only for its original MMO objectives, but also for research on:

- coherent structures;
- horizontal inhomogeneity;
- surface-layer organization;
- convection;
- sweeps and ejections;
- aerosol structure;
- wind-retrieval evaluation;
- spatial turbulence statistics;
- instrument intercomparison;
- boundary-layer evolution.

---

# 19. Public data access

The complete M2HATS project archive is maintained by NSF NCAR/EOL.

A growing subset of M2HATS observations and CSU Chico REAL products is also served directly from:

```text
https://lidar.csuchico.edu/
```

The Chico server is particularly useful for file-level access over HTTPS, including workflows in which Python or MATLAB reads selected files directly from the server without first downloading an entire archive.

For a practical map of the available public data and derived products, see:

```text
M2HATS_data_locations.md
```

---

# 20. Important distinction: experiment overview versus data documentation

This overview explains the **experiment**.

It does not attempt to document every file, variable, processing algorithm, calibration, or data-quality issue.

For quantitative use of a particular observing system, consult the corresponding instrument/data documentation.

Examples include:

```text
REAL_instrument_description.md
REAL_bscan_data_file_format.md
REAL_bscan_signal_processing.md
```

and future guides for:

```text
M2HATS_ISFS_data.md
M2HATS_ISFS_examples.md
Typhoon_overview.md
M2HATS_Typhoon_data.md
```

The NCAR/EOL data reports remain the authoritative detailed references for the NCAR observing systems.

---

# 21. Primary supporting documentation

## Experiment paper

Tong, C., S. D. Mayor, S. P. Oncley, C. Roden, W. O. J. Brown, S. M. Spuler, M. Hayman, B. M. Morley, J. Witte, P. Dérian, S. F. J. De Wekker, J. Sun, K. Barskov, and D. Pourabdollah (2026), "Multipoint Monin-Obukhov Similarity Theory Horizontal Array Turbulence Study (M2HATS)," *Bulletin of the American Meteorological Society*, 107, E501-E527.

```text
https://doi.org/10.1175/BAMS-D-24-0037.1
```

## NCAR/EOL ISFS report

```text
M2HATS NSF NCAR/EOL ISFS Surface Meteorology and Flux Products Data Report
```

This is the detailed reference for the horizontal sonic array, multilevel towers, flux measurements, sensor locations, variable conventions, quality control, and ISFS data products.

## NCAR/EOL ISS wind-lidar report

```text
M2HATS NSF NCAR/EOL ISS Wind Lidar Data Report
```

This describes the WindCube and Halo Doppler lidars, scan modes, pointing geometry, processing, and downloadable products.

## NCAR/EOL ISS surface-met report

```text
M2HATS NSF NCAR/EOL ISS Surface Meteorology, Ceilometer,
PurpleAir and Webcam Products Data Report
```

This describes the ISS surface meteorology stations, ceilometer, PurpleAir sensors, webcams, and related products.

---

# 22. Compact summary for an AI or new user

> M2HATS was a 2023 atmospheric surface-layer field experiment near Tonopah, Nevada, designed primarily to test multipoint Monin-Obukhov similarity theory using spatial turbulence measurements. Its centerpiece was a 245-m horizontal array of 50 sonic anemometers spaced 5 m apart and oriented approximately perpendicular to the prevailing daytime southerly wind. Two multilevel flux towers, REAL scanning aerosol lidar, three Doppler wind lidars, radar wind profilers, RASS, two MicroPulse DIALs, fiber-optic distributed temperature sensing, radiosondes, a profiling drone, and supporting surface measurements extended the observations from meter scales near the ground through kilometer scales in the atmospheric boundary layer. REAL was positioned so that an 80-degree beam direction was collinear with the sonic array, providing an intentional geometrical connection between spatial lidar imagery and dense in-situ turbulence measurements. The resulting data set combines high-frequency point measurements, horizontal spatial fields, and vertical profiles in an unusually comprehensive way.
